Products

Alumina Ceramic Holed plate forming way is isostatic pressing which with higher density , zero porosity .  The holes are machined by cnc machining .  We could reach high tolerance for machining such type of alumina ceramic plate , as fine as 0.005mm. It is used for high temperature resistant application

The processing way of zirconia ceamic threaded rod shaft include as below . 1. Zirconia ceramic Rod Drilling . 2. Ceramic rod slotting: slotting can be carried out according to the requirements of customers, including single-sided slotting and double-sided slotting;

High Temperature Ceramic Tube Diameter 1mm Small size 99% Alumina Ceramic Tube with outside diameter 1mm , inside diameter can be 0.3mm , 0.5mm with different length, it is high temperature resistant which could resistant to 1750 ℃. Properties of

Semiconductor Alumina Ceramic Parts used as semiconductor spare parts Features: 1. arc accuracy is better than ±0.02mm;  2. the precision of all holes is up to ±0.01mm;  Inspection equipment: automatic two - dimensional Checker

3X Ceramic Parts company specialized in alumina ceramic parts precision machining .  Alumina Ceramic material  is a white or beige ceramic, using its excellent electrical insulation. It has been applied to various electronic components in the early stage, and is the lowest cost material in precision ceramics. Our company supply 95%, 99%, 99.5%, 99.8%, 99.9% alumina ceramic precision machining service .

Zirconia Ceramic curved strip is pure machined on CNC machine . It belongs to a special shaped parts .  Curved Zirconia Ceramic Strip  by the customer to provide drawings, manufacturers according to the drawings using equipment to produce the corresponding non-standard special-shaped parts products,

Waterjet intensifier ceramic plunger for water jet pump  with code 010253-1,  it is used on 60k ultra high pressure intensifier  waterject pump 50HP, 60HP,100HP, 40KPSI, 60KPSI  .   The max pressure it undertake can be 60 kpsi , voltage 220v/380v.

Zirconia Ceramic Wafer Carrier Support is highly precision machinind by flapping machine and CNC machined . It is used on the photovaltaic equipment machine to carry the wafer in semiconductor industry .

If the length and width of the zirconia sheet less than 250mm,  and thickness less than 1mm  we could use slip casting forming way for producing those ultra thin zirconia ceramic sheet .  But it also depends on the requirements of the customer on the tolerance , surface finish , strength .  We could also flap a thick zirconia ceramic sheet to the thiner idea thickness , while its cost is much higher than slip casting . The surface could be mirror  polished , roughness could reach as fine as 0.02mm .

High precision Zirconia Ceramic parts with slot ,holes , steps , which are all machinind on CNC machine .  We could get very high precision for some outside dimension , tolerance as high as 0.001mm . This is suitable for some structural parts at small quantity ,  low quantity .  It is no need to pay expensive mould charge to get a few parts to test .  If we have the blank material ,  the machining work is very fast , just take 7 days around to finish .

250x250x3mm  alumina ceramic plate with a purity of 99.7% Aluminum Oxide , it is custom made according to tolerance ISO 2768 mk, sharp edges to be smoothed , used for vacuum material as its high temperature resistance , electrical insulation , chemical resistance , wearable with long working life .  The net weight of each alumina plate is around 720 gram .

The alumina ceramic fixture is used for locating or fixing  products when manufacturing .  Its composition is 99% alumina ceramic , we could also custom make according to customer requirements .  Because of the alumina ceramic material is wearable ,  high temperature resistant , chemical resistant ,  it is a good choice of fixture .  Its properties is stable during various harsh ennironment .

Geometric accuracy: the geometric accuracy of zirconia ceramic shaft  mainly refers to the roundness and cylindricity of journal, outer cone, Morse taper hole, etc., and the general tolerance shall be limited to the dimensional tolerance. For the inner and outer circular surfaces with high accuracy requirements, the allowable deviation shall be marked on the drawing.

Ceramic Wafer Carrier Support Plate is made of zirconia ceramic material , this is because zirconia ceramic surface is more smooth after polished , its roughness could reach to below  Ra 0.1, so it is more easy to clean .  Also this material is chemical resistant , wearable last long time , high temperature resistant and with good strength .

Alumina Ceramic Robot Arm CNC machined The ceramic robot arm provided by our company is mainly divided into clamping type, bearing type and vacuum adsorption type. The sizes are 2 ", 4", 6 ", 8", 12 ", and non-standard sizes can be customized.

Zirconia ceramic ball valve seat used for fluid control Sucker Rod Pumps , the ball match with it is 12mm silicon nitride material .  Find Complete Details about Ceramic Valve Ball And Valve Seat For Sucker Rod Pumps,Ceramic Valve Ball Valve Seat from Valves Supplier

Silicon Carbide sleeve bearing  is mainly used for shielding pump and magnetic pump for conveying medium, and can also be used for other. The utility model relates to a shaft sleeve for a silicon carbide sliding bearing, which is sleeve shaped. The utility model is characterized in that both ends of the inner side of the shaft sleeve are fixed mating

Pressureless sintered silicon carbide shaft has corrosion resistance, high temperature resistance, wear resistance, non-magnetic, non-conductive and good self lubrication. It has excellent chemical corrosion resistance, wear resistance, high temperature resistance, high mechanical strength, good self-lubricating performance, high temperature creep resistance, low friction coefficient, high thermal conductivity and low thermal expansion coefficient.